Foundations for timber houses: how to design the base connection correctly

When looking at a timber house, attention almost always goes to the walls, the roof and the quality of the interior spaces. Yet a decisive part of the project lies lower down, where the timber structure meets the foundation.

The foundations of a timber house are normally built with mineral materials, most often concrete. They must transfer loads to the ground and create a stable, precise base protected from moisture on which the prefabricated elements can be installed.

This transition cannot be treated as a minor site detail. Slab geometry, levels, anchors, waterproofing, insulation, service penetrations and airtightness must all be coordinated before the walls arrive on site.

For timber construction in Ticino and elsewhere in Switzerland, careful design of the base connection supports structural durability, continuity of the building envelope and a predictable installation process.

A durable timber house begins where the wood meets the ground: the base connection must stop water, moisture and heat loss before they reach the structure.

The foundation is not timber, but it determines how the house performs

A timber building is light compared with many conventional solutions, but this does not make the foundation secondary. The system must still transfer the weight of the building, imposed loads and the effects of wind and earthquakes safely into the ground.

The choice depends on the soil, the slope, the presence of a basement, the building geometry and the structural design. A continuous raft slab may be suitable for a single-family home; in other cases, strip foundations, retaining walls or specific solutions defined by the engineer may be more appropriate.

There is therefore no universal foundation for timber houses. There is only a solution that is consistent with the ground conditions and the chosen construction system.

Raft slab, basement or strip foundations

A concrete raft slab is widely used because it provides a continuous surface on which to set out the walls and simplifies coordination between structure, insulation and building services. On sloping sites, which are common in Ticino, the design may require retaining walls, split levels or a partially buried storey.

Where there is a room against the ground, waterproofing and drainage become even more important. If the building has no basement, the junction between the floor, the slab edge and the external wall becomes the key detail to resolve.

The decision must be made together with the architectural and structural design because it affects levels, access points, thresholds, services and the installation sequence.

The junction between timber and concrete is the most sensitive detail

Timber should not be in direct contact with surfaces that can transfer moisture. Separation layers, gaskets and sealing systems compatible with the building-envelope build-up are therefore installed between the foundation and the wall.

The height of the timber above the external ground level also matters. Rainwater, snow, splashback and standing water must be kept away from the structure through a correctly designed plinth, effective falls and coordinated external landscaping.

Lignum draws particular attention to the connections between timber structures, plinths and foundations. These are technical interfaces where constructional moisture protection must be resolved with particular care.

  • a capillary break between mineral elements and timber;
  • protection of the plinth from water and splashback;
  • continuity of sealing and airtight membranes;
  • drainage and falls to external surfaces.

Geometric accuracy and tolerances for prefabrication

Prefabricated walls are manufactured to defined dimensions. When they arrive on site, the foundation must match the design in terms of level, flatness and anchor positions.

A deviation of a few millimetres may be manageable, but repeated errors or inconsistent levels can delay installation and make the junctions with floors, windows and façades more difficult.

This is why surveying the foundation before production or installation is important. It allows diagonals, levels, bearing points and service provisions to be checked while orderly corrections are still possible.

Moisture control and durability are designed before installation

Timber can provide a long service life when it is kept within the conditions assumed by the design. The risk does not come from the material itself, but from water reaching sensitive points and remaining there.

Both the foundation and the prefabricated elements must be protected during construction. Damaged membranes, water on the slab or closing the build-up before it has dried can compromise a junction that will be difficult to inspect once the building is complete.

SIA 180 treats thermal insulation, moisture protection and indoor climate as interconnected issues. In timber construction, this means build-ups that limit water ingress, control vapour and allow the element to perform under the intended hygrothermal conditions.

The slab edge must limit thermal bridges

The junction between the floor and the external wall is also sensitive from an energy perspective. If the floor insulation, façade insulation and plinth are not coordinated, a discontinuity can form that increases heat loss and lowers internal surface temperatures.

A lower surface temperature near the floor can reduce comfort and, in unfavourable conditions, increase the risk of condensation. The solution is not simply to add more insulation, but to design the thermal layer continuously around the junction.

This detail must be assessed together with the wall build-up, the finished floor level and the façade system.

Airtightness, service penetrations and radon

Drainage pipes, water supplies, electrical cables and other services often pass through the slab or walls in contact with the ground. Every penetration must be located before the concrete is poured and fitted with a suitable sealing system.

Correcting a pipe that has been placed in the wrong position can require local demolition and create points that are difficult to seal. With prefabrication, it is therefore essential that structural, building-services and architectural designs use the same coordinates.

Continuity of the parts in contact with the ground is also important for radon protection. The Swiss Federal Office of Public Health recommends addressing the issue at the design stage of new buildings, with particular attention to continuity of the slab and sealing around pipe and cable penetrations.

Anchors and load transfer

Timber elements must be connected to the foundation so that horizontal forces, uplift and shear are transferred correctly. Plates, brackets, anchor bolts and hold-downs are sized to suit the structural design.

Anchor positions cannot be decided during installation. They must take account of the wall structure, openings, panel joints and reinforcement within the concrete.

A good detail must be structurally effective while remaining compatible with insulation, airtightness and moisture protection. It is precisely where these requirements overlap that technical coordination adds value.

Thresholds, glazed doors and step-free access

Openings onto terraces and gardens require care because they bring together the internal floor, threshold, waterproofing and external level.

A nearly flush entrance can improve accessibility but reduces the margin available to protect the junction from splashback and standing water. Falls, drainage and specific interfaces must therefore be designed before the door or window is installed.

The correct detail depends on façade exposure, the presence of canopies, the type of external paving and the building-envelope build-up.

From pouring the slab to installing the walls

A well-organised sequence reduces corrections on site. Once the foundation has been completed, its geometry, levels, provisions and drying conditions are checked. Only then are the prefabricated elements and installation method finally confirmed.

On installation day, bearing components, gaskets, anchors and protection must already be available and consistent with the construction drawings. The walls can then be placed, braced and connected in sequence without interrupting the workflow to resolve missing details.

  • checking the bearing plane and diagonals;
  • verifying service penetrations;
  • installing separation and sealing layers;
  • erecting and bracing the elements;
  • structural fixing and closing the junctions.

The role of Project Evolution

For Project Evolution, the quality of a timber building depends on continuity between design, supply, logistics and installation. The foundation junction clearly illustrates this approach: structure, envelope, services and site organisation all meet at the same point.

Resolving these aspects before production means installation can begin with verified details and coordinated materials. This is important both for a complete house and for a building delivered as an advanced shell, with the envelope complete and the interior ready for the subsequent trades.

If you are considering a timber house or structure in Ticino, involving a specialist from the earliest stages helps verify feasibility, the construction system and the working sequence.

Frequently asked questions about timber house foundations

What type of foundation does a timber house need?

It depends on the soil, slope, geometry and the presence of below-ground spaces. A raft slab, strip foundations or a combined solution must be defined by the structural design and coordinated with the timber system.

Can a timber house be built on a concrete slab?

Yes. A continuous raft slab is a common solution because it provides a stable installation surface and makes it easier to coordinate structure, insulation and building services.

How is timber protected from moisture in the foundation?

The design coordinates levels, capillary breaks, membranes, plinth protection, falls and drainage. Timber must remain separated from water and standing moisture.

Why is slab flatness so important?

Prefabricated elements are manufactured to precise dimensions. A base with correct levels, flatness and diagonals allows walls and floors to be installed without improvised adjustments.

Can the foundation edge create a thermal bridge?

Yes. The junction between the floor, plinth and wall must maintain continuous insulation to limit heat loss and cold internal surfaces.

How are timber walls fixed to the foundation?

They are fixed with anchoring systems sized by the structural engineer, such as plates, brackets, anchor bolts and hold-downs. Their number and position depend on the expected actions and the construction system.

Do foundations need to address radon?

Yes. In Switzerland, radon must be considered from the design stage, especially for parts of the building in contact with the ground. Slab continuity and sealed service penetrations are central.

When should service provisions be defined?

Before the foundation is poured. Drainage, water supplies and electrical penetrations must match the design of the prefabricated walls and internal service zones.